Garmin PRO Control 2 Manuel du propriétaire télécharger pdf (Page 8)

Mode Top Key Middle Key Bottom Key Description

TVM Tone Vibration Momentary

(low)

Beginning trainer,

sensitive dog, or

minor corrections

VCM Vibration Continuous

(high)

Momentary

(high)

All-around training

TCM Tone Continuous

(high)

Momentary

(high)

All-around training

CMM Continuous

(high)

Momentary

(high)

Momentary

(low)

Advanced

training, popular

for bird-dog

training

MCC Momentary

(high)

Continuous

(high)

Continuous

(low)

Advanced

training, popular

for obedience

training

Selecting a Training Mode

You can select a different training mode for each dog collar

device.

Select a dog collar device (Selecting a Dog Collar Device).

Select RAPID LAUNCH to toggle through the available

training modes.

Choosing the Correct Intensity Level

Set the intensity to the lowest level (Changing the Intensity

Level).

Press a training key.

Observe the dog for a reaction, such as a head shake, neck

movement, or just a change in expression.

Sometimes dogs will vocalize due to the surprise of the

electrical stimulation. If the dog vocalizes more than once,

the intensity level is too high for beginning training.

If there is no reaction, increase the intensity level by one level

until the dog has a slight but recognizable reaction to the

stimulation.

The intensity level that causes a slight but recognizable reaction

is your dog's baseline level for beginning collar training. You do

not need to, and should not, apply this intensity selection test

again.

After you begin training, the dog’s performance guides your

intensity selection. As the dog advances in training, you may

need to change the level depending upon the training situation.

Changing the Intensity Level

You can select a different intensity level for each dog collar

device.

Select a dog collar device (Selecting a Dog Collar Device).

Select or to increase or decrease the intensity level.

The numerical intensity level appears on the LCD display.

TIP: You can hold or to cycle through intensity levels

quickly.

Device Information

PRO Control 2 Handheld Device

Specifications

Battery type Rechargeable, replaceable lithium-ion

Operating temperature range From -4° to 158°F (from -20° to 70°C)

Charging temperature range From 32° to 104°F (from 0° to 40°C)

Storage temperature range From -4° to 122°F (from -20° to 50°C)

Water rating IEC 60529 IPX7*

*The device withstands incidental exposure to water of up to 1 m

for up to 30 min. For more information, go to www.garmin.com

/waterrating.

PRO Control 2 Battery Replacement

Instructions

WARNING

This product contains a lithium-ion battery. To prevent the

possibility of personal injury or product damage caused by

battery exposure to extreme heat, store the device out of direct

sunlight.

Do not use a sharp object to remove batteries.

CAUTION

Contact your local waste disposal department to properly

recycle the batteries.

PRO Control 2 Handheld Device Components

Security screws

Back plate

Battery

Battery connector

Gasket

Replacing the PRO Control 2 Handheld Device Battery

Before you replace the battery, you must remove all dirt, water,

and debris from the device. You also need the security

screwdriver included with the new battery.

You can purchase a replacement battery at

http://buy.garmin.com. You should use only an official Garmin

replacement part.

Remove the six security screws from the back of the device.

Lift up the back plate.

Grip the battery connector wires close to the connector, and

pull the connector parallel to the circuit board to disconnect

the battery connector from the device.

Remove the old battery from the back plate, noting the

orientation of the battery.

The battery fits tightly. It may be necessary to pry the battery

out of the back plate using a non-sharp, non-metal object.

Install the new battery into the back plate with the label side

up, using the same orientation as the old battery.

With the new battery, connect the battery connector to the

device.

When properly installed, the connector plug snaps into the

port.

Verify the gasket is not damaged and is completely seated in

the groove.

Hold the back plate and the device firmly together, and

replace all six security screws without tightening.

Verify the back plate and the device are aligned with no gaps.

Tighten the screws evenly.

4 Device Information

1 2 3 4 5 6 7 8 9 10 11 12

Commentaires sur ces manuels

Pas de commentaire

Garmin PRO Control 2 Manuel du propriétaire Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Soins des animaux Garmin PRO Control 2